|
|
|
|
|
|
HEATED SHELF WITH SENSOR
|
|
|
Heated Shelf with Sensor, for use with Bulk Tray Dryer. 200-watt heater ensures efficient heating from -20ºC to 60ºC. A microprocessor in the Bulk Tray Dryer maintains system temperature within 3ºC of set point.
|
|
|
|
|
|
|
|
|
|
Thermoplastic Duct & Ducting Parts
|
|
|
Thermoplastic Duct. 10' length. PVC exhaust duct is Type I, unplasticized, schedule 40, lightweight and corrosion-resistant. A Female Duct Coupling is required to join two sections.
|
|
|
|
|
|
|
|
|
|
Freeze Dryer Valve Kit
|
|
|
Replacement Freeze Dry Valve Kit, for drying chambers and manifolds manufactured after March, 1996. Fabricated of a neoprene body and gaskets, molded plastic knob and fittings. The valve is easy to replace and accommodates both 1/2" and 3/4" adapters
|
|
|
|
|
|
|
|
|
|
Submicron Composite Vent Kit-Prodigy
|
|
|
Submicron Composite Vent Kit - Prodigy
|
|
|
|
|
|
|
|
|
|
MANIFOLD FOR FREEZONE SYSTEMS
|
|
|
FreeZone Stoppering Tray Dryer, FreeZone Bulk Tray Dryer Applicable Products
|
|
|
|
|
|
|
|
|
|
Auxiliary-Air Plenum Kit for Protector Laboratory Hoods
|
|
|
Auxiliary-Air Plenum Kit, provides a means to introduce supplemental air for the hood exhaust and limit the percentage of tempered air removed from the laboratory. Includes glacier-white epoxy-coated steel plenum that replaces the hood's front panel,
|
|
|
|
|
|
|
|
|
|
Bench-Mounted Secondary Vacuum Trap
|
|
|
For processing samples with low eutectic points. Trap connects in series with a freeze dry system and vacuum pump to prevent contaminants from migrating into the vacuum pump. An insulated well, when dry ice and solvent are added, cools to approximate
|
|
|
|
|
|
|
|
|
|
Solvent Trap
|
|
|
Solvent Trap Insert, contains activated carbon. Protects the rotary vane vacuum pump.
|
|
|
|
|
|
|
|
|
|
Oxygen/Natural Gas Sealing Torch, EA
|
List Price: $861.90
Our Price: $845.00
Limited Time Promotion $775.71 EA
You save $86.19!
|
|
|
Sealing torch^ Oxygen/natural gas sealing torch. Freeze dry accessory.
|
|
|
|
|
|
|
|
|
|
Spiral Tube for Labconco Fume Hoods
|
|
|
Spiral Tube. 10' length. Corrosion-resistant, neoprene-impregnated fiberglass reinforced with steel wire. Includes rigid duct connector and two clamps. Because this ductwork is flexible and may conform to various configurations, it is not possible to
|
|
|
|
|
|
|
|
|
|
Elbow Coupling Ducting Parts
|
|
|
Elbow Coupling Ducting Parts
|
|
|
|
|
|
|
|
|
|
Carbon Filter Pack
|
|
|
Carbon Filter Pack. Activated Carbon Filter for non-radioactive organic vapors and odor control. Rated for 1000 CFM air flow with 0.2" static pressure drop.
|
|
|
|
|
|
|
|
|
|
Protector* FilterMate* Mobile Stations Accessories
|
|
|
Protector* FilterMate* Mobile Stations Accessories
|
|
|
|
|
|
|
|
|
|
Protector ClassMate Hood
|
|
|
The patented Protector ClassMate Laboratory Hood is designed to meet the needs of instructional laboratories. Clear back and sides and taller front viewing window provide enhanced visibility for conducting chemistry demonstrations or observing studen
|
|
|
|
|
|
|
|
|
|
Protector ClassMate Combination Sash Hood
|
|
|
The patented Protector ClassMate Laboratory Hood is designed to meet the needs of instructional laboratories. Clear back and sides and taller front viewing window provide enhanced visibility for conducting chemistry demonstrations or observing studen
|
|
|
|
|
|
|
|
|
|
Protector ClassMate Work Surface
|
|
|
The patented Protector ClassMate Laboratory Hood is designed to meet the needs of instructional laboratories. Clear back and sides and taller front viewing window provide enhanced visibility for conducting chemistry demonstrations or observing studen
|
|
|
|
|
|
|
|
|
|
Protector Premier Fiberglass-Lined Hood
|
|
|
The Protector Premier Laboratory Hoods incorporate a redesigned, sleek exterior with a one-piece fiberglass reinforced polyester liner, the signature feature of leading line of fume hoods since 1961. The liner has many benefits. Fiberglass is corrosi
|
|
|
|
|
|
|
|
|
|
SpillStopper Work Surface for Protector XStream Hoods
|
|
|
SpillStopper Work Surface, solid epoxy, 1.25" thick, dished to retain spills and has a 1" radiused front edge to direct airflow into the hood. For Protector XStream Laboratory Hoods.
|
|
|
|
|
|
|
|
|
|
Vibration Isolation Table, EA
|
List Price: $1,004.70
Our Price: $985.00
Limited Time Promotion $934.37 EA
You save $70.33!
|
|
|
Vibration Isolation Table^ For conducting procedures with vibration-sensitive equipment. Epoxy-coated steel frame, adjusts in 2.5cm increments. Work surface is laminated hard board. Four leveling feet included. Dimensions: 82.6Wx63.5Dx74.9-91.4Hcm. S
|
|
|
|
|
|
|
|
|
|
Protector Perchloric Acid Laboratory Hood with Work Surface
|
|
|
Protector Stainless Steel Perchloric Acid Laboratory Hoods are designed specifically for procedures involving the use of perchloric acid. They feature washdown systems, integral work surfaces and drainage troughs so that they may be thoroughly rinsed
|
|
|
|
|
|
|
|
|
|
Protector Acid Digestion Laboratory Hood with Work Surface
|
|
|
Protector PVC Acid Digestion Laboratory Hood, by-pass airflow design, heat-welded unplasticized PVC interior with integral work surface and drainage trough, 1/4" thick Lexan sashes to prevent etching caused by Hydrofluoric Acid (HF) fumes, built-in w
|
|
|
|
|
|
|
|
|
|
Protector Radioisotope Laboratory Hood with Work Surface
|
|
|
Protector Stainless Steel Radioisotope Laboratory Hoods provide protection from applications requiring the use of radiochemicals. They feature fully sealed integral work surfaces and coved interiors to facilitate decontamination.Available in 4, 5, 6
|
|
|
|
|
|
|
|
|
|
Coated Steel Blower EP
|
|
|
Coated Steel Blower, recommended for low to moderately corrosive applications. Features: Non-sparking aluminum impellers and UL listed explosion-proof motor for maximum safety; phenolic coating on impeller and housing is corrosion resistant; dry powd
|
|
|
|
|
|
|
|
|
|
FIBERGLASS BLOWER
|
|
|
Fiberglass Blowers are ideal for fume hood exhaust systems in moderate to highly corrosive conditions. The molded fiberglass reinforced polyester housing provides superior corrosion resistance. Fiberglass Blowers are available that deliver as little
|
|
|
|
|
|
|
|
|
|
PVC Blower
|
|
|
PVC Blowers provide optimum chemical resistance and are made specifically to handle high order oxidizers such as perchloric acid. The housings are vacuum formed from unplasticized Type I polyvinyl chloride to handle highly corrosive applications. The
|
|
|
|
|
|
|
|
|
|
Mobile Bench, EA
|
List Price: $928.20
Our Price: $910.00
Limited Time Promotion $863.23 EA
You save $64.97!
|
|
|
Fixed Height Mobile Bench^ Holds up to 245kg. Work space plus mobility. Chemical- and heat-resistant top. Centered lower support bar. Frame of 18-gauge steel tubing. 12.7cm diameter non-marking polyurethane locking casters. Assembled. Dimensions: 122
|
|
|
|
|
|
|
|
|
|
Manual Duct Damper
|
|
|
Manual Duct Damper. Damper fitting allows you to balance airflow. Used with exhaust and auxiliary-air ducts, and is usually placed directly above the fume hood.
|
|
|
|
|
|
|
|
|
|
Flexible Duct Connection for 8" dia. duct, EA
|
List Price: $160.14
Our Price: $157.00
Limited Time Promotion $148.93 EA
You save $11.21!
|
|
|
Flexible Duct Connection^ Reduces vibration between the blower and PVC ductwork. Includes two clamps for easy installation. 9" diameter for use with 8" diameter duct. 12" high.
|
|
|
|
|
|
|
|
|
|
Blower Transition Adapter, 10" dia., EA
|
List Price: $275.40
Our Price: $270.00
Limited Time Promotion $256.12 EA
You save $19.28!
|
|
|
Blower Transition Adaptor^ Epoxy-coated steel. Allows connection of thermoplastic duct to the exhaust side of a Coated Steel Blower. PVC duct fits inside the adaptor opening. 5.5 x 10" rectangular inlet. 10" nominal diameter outlet. 10.84" high.
|
|
|
|
|
|
|
|
|
|
|
Rear Finish Panel Kit
|
|
|
Rear Finish Panel Kit. The panel hides the hood's interior components. Recommended when hoods is mounted on a casework island. Kit includes glacier white epoxy-coated steel panel to provide a finished appearance for the rear of the hood.
|
|
|
|
